TOPLEVEL PARAMETERS
                              -------------------

Method Information For: D:\MSDCHEM\1\METHODS\2_SCREEN.M

Method Sections To Run:

  (X) Save Copy of Method With Data
  ( ) MSTOP              Pre-Run Cmd/Macro  =  
  ( ) Instrument Control Pre-Run Cmd/Macro  =  
  ( ) Data Analysis      Pre-Run Cmd/Macro  =  
  (X) Data Acquisition      
  (X) Data Analysis         
  ( ) MSTOP              Post-Run Cmd/Macro =  
  ( ) Instrument Control Post-Run Cmd/Macro =  
  ( ) Data Analysis      Post-Run Cmd/Macro =  
Method Comments:
  This is the default method


                              END OF TOPLEVEL PARAMETERS
                              --------------------------







                              INSTRUMENT CONTROL PARAMETERS
                              -----------------------------

=============================================================================
                               6890 GC METHOD
=============================================================================

OVEN
   Initial temp:  40 'C (On)               Maximum temp:  350 'C
   Initial time:  0.00 min                 Equilibration time:  0.50 min
   Ramps:
      #  Rate  Final temp  Final time
      1  5.00      320        4.00
      2   0.0(Off)
   Post temp:  0 'C
   Post time:  0.00 min
   Run time:  60.00 min

FRONT INLET (HP PTV)                    BACK INLET (UNKNOWN)
   Mode:  Splitless
   Initial temp:  40 'C (On)
   Initial time:  0.00 min
   Ramps:
      #  Rate  Final temp  Final time
      1600.00      320        2.00
      2 10.00      200        0.00
      3   0.0(Off)
   Cryo:  On
   Cryo use temp:  200 'C
   Cryo Timeout:  30.00 min (On)
   Cryo Fault:  Off
   Pressure:  83.0 kPa (On)
   Purge flow:  50.0 mL/min
   Purge time:  1.00 min
   Total flow:  54.5 mL/min
   Gas saver:  On
   Saver flow:  20.0 mL/min
   Saver time:  2.00 min
   Gas type:  Helium

COLUMN 1                                COLUMN 2
   Capillary Column                        (not installed)
   Model Number:  Resteck Rxi-5ms
   Serienummer 864841
   Max temperature:  350 'C
   Nominal length:  30.0 m
   Nominal diameter:  250.00 um
   Nominal film thickness:  0.25 um
   Mode:  constant flow
   Initial flow:  1.5 mL/min
   Nominal init pressure:  82.5 kPa
   Average velocity:  44 cm/sec
   Inlet:  Front Inlet
   Outlet:  MSD
   Outlet pressure:  vacuum

FRONT DETECTOR (NO DET)                 BACK DETECTOR (NO DET)

SIGNAL 1                                SIGNAL 2
   Data rate:  20 Hz                       Data rate:  20 Hz
   Type:  test plot                        Type:  test plot
   Save Data:  Off                         Save Data:  Off
   Zero:  0.0 (Off)                        Zero:  0.0 (Off)
   Range:  0                               Range:  0
   Fast Peaks:  Off                        Fast Peaks:  Off
   Attenuation:  0                         Attenuation:  0

COLUMN COMP 1                           COLUMN COMP 2
   (No Detectors Installed)                (No Detectors Installed)

THERMAL AUX 2
   Use:  MSD Transfer Line Heater
   Description:
   Initial temp:  320 'C (On)
   Initial time:  0.00 min
      #  Rate  Final temp  Final time
      1   0.0(Off)

                                        POST RUN
                                           Post Time: 0.00 min

TIME TABLE
   Time       Specifier                     Parameter & Setpoint


                              7673 Injector


     Front Injector:
        Sample Washes                 2
        Sample Pumps                  3
        Injection Volume            1.0 microliters
        Syringe Size               10.0 microliters
        PostInj Solvent A Washes      3
        PostInj Solvent B Washes      0
        Viscosity Delay               0 seconds
        Plunger Speed              Fast
        PreInjection Dwell         0.00 minutes
        PostInjection Dwell        0.00 minutes
        Sampling Depth              0.0 mm

     Back Injector:
No parameters specified

 Column 1 Inventory Number :  
 Column 2 Inventory Number :  

                                MS ACQUISITION PARAMETERS


General Information
------- -----------

Tune File                : dftpp.u
Acquistion Mode          : Scan


MS Information
-- -----------

Solvent Delay            : 2.60 min

EM Absolute              : False
EM Offset                : 0
Resulting EM Voltage     : 2329.4

[Scan Parameters]

Low Mass                 : 30.0
High Mass                : 550.0
Threshold                : 150
Sample #                 : 2       A/D Samples    4

[MSZones]

MS Quad                  : 150 C   maximum 200 C
MS Source                : 230 C   maximum 250 C


                             END OF MS ACQUISITION PARAMETERS


                           END OF INSTRUMENT CONTROL PARAMETERS
                           ------------------------------------